RUT200

Teltonika RUT200

RUT200 is a compact industrial 4G (LTE) router equipped with 2x Ethernet ports, WiFi and RutOS software for advanced networking solutions.

General

* Order code dependant.

** Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

RF exposure

This device meets the official requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by authorized agencies. The device must be used with a minimum separation of 20 cm from a person’s body to ensure compliance with RF exposure guidelines. Failure to observe these instructions could result in your RF exposure exceeding the applicable limits.

External antennas used with RUT200 must be installed to provide a distance of at least 20 cm from any people and must not be co-located or operated in conjunction with any other antenna or transmitter.

Any external antenna gain must meet RF exposure and maximum radiated output power limits of the applicable rule section.

Operating conditions

• Operating temperature: -40° to +75° Celsius
• Humidity should be in the range of 10% to 90% (non-condensing). Only use the device in dry environments.
• Out of direct sunlight
• Away from heat source, corrosive substances, salts, and flammable gases

Attention: operation outside the permissible range can considerably shorten the service life of the device.

Faulty and damaged products

• Do not attempt to disassemble the device or its accessories.
• Only qualified personnel must service or repair the device or its accessories.
• If your device or its accessories have been submerged in water punctured or subjected to a severe fall, do not use until they have been checked at an authorized service center.

Electrical safety

• Only use approved accessories.
• Do not connect with incompatible products or accessories.
• It is recommended to ground devices with grounding terminals before connecting them to power. Failure to ground appropriately might result in a shock hazard. The cross-sectional area of the protective grounding conductor should be at least 1mm2.

Product handling

• You alone are responsible for how you use your device and any consequences related to its use.
• Use of your device is subject to safety measures designed to protect users and their environment.
• Always treat your device and its accessories with care and keep it in a clean and dust-free place.
• Do not expose your device or its accessories to open flames, lit tobacco products, liquid, moisture, or high humidity.
• Do not drop, throw or try to bend your device or its accessories.
• Do not use harsh chemicals, cleaning solvents, or aerosols to clean the device or its accessories.
• Do not paint your device or its accessories.
• Do not attempt to disassemble your device (exemptions for devices that require disassembly for SIM insertion) or its accessories: it does not contain any user-serviceable parts. For safety reasons, the equipment should be opened only by qualified personnel.
• Make sure to use ESD personal protective equipment while the equipment is serviced.
• Do not use your device in an enclosed environment where heat dissipation is poor.
• Prolonged use in such space may cause excessive heat and raise ambient temperature, which will lead to the automatic shutdown of your device or the disconnection of the mobile network connection for your safety. To use your device again after such a shutdown, cool it in a well-ventilated place before turning it on.
• Please check all national laws and local regulations for the disposal of electronic products.
• Do not operate the device where ventilation is restricted.
• Do not use or install this product near water to avoid fire or shock hazards.
• Avoid exposing the equipment to rain or damp areas.
• Arrange power and Ethernet cables so that they are not likely to be stepped on or have items placed on them.
• Ensure that the voltage and the rated current of the power source match the device’s requirements. Do not connect the device to an inappropriate power source.
• During a thunderstorm, no operations should be carried out on the device and cables.
• The unit must be powered off where blasting is in progress and explosive atmospheres are present or near medical life support equipment.
• Do not leave your device and its accessories within reach of small children or allow them to play with it. They could hurt themselves or others and could accidentally damage the device. Your device contains small parts with sharp edges that may cause an injury choking hazard.
• Like any wireless device, this device operates using radio signals, which cannot guarantee connection in all conditions. Therefore, you must never rely solely on any wireless device for emergency communications or otherwise use the device in situations where the interruption of data connectivity could lead to death, personal injury, property damage, data, or other loss.
• The device may become warm during regular use.